How to Install Aluminum Doors and Windows Correctly? -Ruminum Profiles Supplier

There is a saying in the industry: production three points and seven points for installation. Talk about the importance of doors and windows installation. Good doors and windows need good installation technicians and good installation skills.

If it is not installed properly, good doors and windows may be regarded as inferior products.

1. Before installing, you need to prepare various tools, drawings, customer contact information and installation materials. When installing, consider the accidental emergency situations that may occur, prepare all the tools that may be used, and do not wait until the problem is resolved. You must make predictions and preparations in advance so that you can calmly cope with the emergencies. It will not cause work loss. Commonly used tools are: screwdriver, inner hexagon wrench, electric diamond, sealing gum, foam polystyrene, seat belt, safety rope, air compressor, brush, tools, nail guns, screws and expansion bolts.

2. After delivery of the material handling goods to the construction site, the window frame and glass need to be delivered indoors. It must be used when there is an elevator.

If the elevator cannot be used, you can choose the stairs.

If the stairs cannot be used, appropriate lifting equipment can be used. When dealing with materials, please hold it firmly and pay attention to safety. When processing the glass, use the suction cup as much as possible to prevent damage to the glass. Do not expose the glass, so as not to cause damage to the body after the glass is broken! If there is no lifting device and the window is too large, if you need to manually pull out the window, you must use a rope to tighten the window. There are enough people. Do not work during the wind and pay attention to safety.

3. After the window installation is transported to the installation position, the installation can be started.

If there are furniture at the door and window installation site, the location needs to be protected, and the furniture of customers must be safely protected before installation.

If there is no furniture, this step can be omitted. Before installation, check the installation location of the window frame correct, otherwise you may need to be reinstalled. There are two ways to repair the window.

Usually, fixing with fixed parts, the other is to fix the installation hole with expansion bolts. Put the window frame in the hole, adjust the front and rear positions in the hole, and adjust the gap between the window frame to the uniform state. The adjustment process requires the appropriate diagonal pad (similar to the diagonal cushion of mechanical installation). It can be made of wood or a finished product purchased in the market. There are also special air cushions. It is easy to adjust. After adjusting the gap, you can fix the window frame first without the need for people to continue holding the window frame. Use laser marks to adjust the horizontal and verticality of the doors and windows, and adjust the doors and windows well. After that, the rest can be fixed. After the doors and windows are fixed, pay attention to check carefully during the fixed doors and windows to prevent the window frame movement and make the doors and windows a horizontal and vertical state.

If it is a passive window, there will be some special requirements during installation.

For example, a special thin film should be pasted in the inner and outer side of the window frame. The heat bridge and anti -corrosion treatment should be performed on the fixed plate for fixing, and a pre -compressed sealed tape is pasted between the windows. Frames and walls.

4. After sealing the location of the fixed window, the gap between the doors and windows and the walls need to be sealed. Polyurethane foam is usually used for sealing. Before using the foam polystyrene, the water should be sprayed to the glue part to enable the foam polystyrene to better swell and achieve the best sealing effect. After the foaming glue is completed, wait for the foaming glue to solidify and harden. During this time, do not perform other tasks to make the foam glue completely swell. After the foam polystyrene is cured, cut off the excess foam with a wallpaper knife. You can then engage in the work of outdoor seals.

5. The glass installation is installed on the window frame according to the drawings and glass tags. The installation techniques of glass should be paid attention to distinguish fixed glass and fans. Make sure to pay attention to the installation of glass partitions, especially when opening the fan glass.

If the glass mat is not installed correctly, the window frame will be drooping. The glass sagging caused by this situation cannot be achieved by adjusting the hardware. When installing the glass, please pay attention to the direction, inside and outside, and 3C logo. For LOWE glass, it should be placed on the interior; for fire -resistant glass, it should be placed outdoors; for matte glass, the scrub surface should be placed on the side where the water cannot contact.

6. After the fan installation is installed, the fan fan can be installed. Install the corresponding fan to the corresponding position according to the label. After installing a fan, the opening of the doors and windows should be flexibly. Hardware can usually be adjusted on three dimensions, but the adjustment volume is not large. According to the requirements for doors and windows processing accuracy, the hardware has good processing accuracy. When debugging the hardware during the production phase, there is basically no problem, and there is no need to be too much when installing at the scene. 7. Sort and clean the installation site and maintain good on -site hygiene. Sort the installation tools and remaining materials. Let customers fill in the feedback form, explain the relevant knowledge about doors and windows maintenance and use, and leave a after -sales phone. After completing the above steps, the doors and windows can be installed correctly.